Извините, этот техт доступен только в “Американский Английский”. For the sake of viewer convenience, the content is shown below in the alternative language. You may click the link to switch the active language.
TECHNICAL PRINCIPLES FOR CREATING A WIRELESS LOCAL NETWORK WI-FI
Albina Y. Sharifullina, Kazan National Research Technological University, Kazan, Russia, albina.090904@gmail.com
Roman R. Galyamov, Kazan National Research Technological University, Kazan, Russia, sautp@yandex.ru
Rimma S. Zaripova, Kazan National Research Technological University, Kazan state power engineering University, Kazan, Russia, zarrimma@mail.ru
Abstract
This article discusses the stages of development, characteristics of a wireless local area network Wi-Fi, options for its topology and equipment used. Currently, there are such different types of wireless networks as Wireless Wide Area Network, Wireless Metropolitan Area Networks (Wireless Neighborhood Area Network), Wireless Local Area Network, Wireless Personal Area Network. Each of the listed wireless networks has its own specific range and application. Wireless LAN Wi-Fi refers to the Wireless Local Area Network. The first wireless LAN standard, Wi-Fi, was approved in 1997. From the moment of their appearance to the present day, the following standards of this network have appeared: 802.11a, 802.11b, 802.11g, 802.11n, 802.11ac, 802.11ad, 802.11ax. For each standard, the speeds and frequency ranges at which the data transmission was carried out are indicated, and the technologies on which they are built are described. Wireless LAN Wi-Fi has three topologies: 1) Ad-Hoc (point-to-point) or Independent Basic Service Set; 2) Basic Service Set («client / server») and 3) Extended Service Set («extended service areas»). To build a Wi-Fi network, network adapters, access points, routers, ADSL modems, Wi-Fi phones, Wi-Fi antennas, Wi-Fi repeaters are used. Wi-Fi adapters are used by devices that do not have a built-in Wi-Fi module. Wi-Fi access points are designed for organizing wireless access within a local network. Wi-Fi routers are designed to route traffic on a computer network. ADSL modems are used to access the Internet over a telephone line. Wi-Fi repeaters are used to expand the coverage of a wireless network using already installed equipment. Wi-Fi phones are wireless IP phones. Wi-Fi antennas are used to extend the range of a wireless network.
Keywords: wireless networks, IEEE 802.11, Wi-Fi, data transfer rate, the principle of creating computer networks.
References
1. A.V. Chupaev, A.Yu. Sharifullina, A.N. Akhmerova, A.Yu. Sharifulin (2018). Wireless industrial networks based on ISA-100.11.a and WirelessHART. Calculation of the main energy and information parameters. Bulletin of Kazan Technological University. Vol. 21. No. 7. P. 116-120.
2. A.Yu. Sharifullina, A.N. Akhmerova, R.S. Zaripova (2019). Development of a wireless data transmission network based on isa100.11a standard in the training laboratory «Yokogawa». T-Comm. Vol. 13. No. 11. P. 20-24.
3. A.V. Chupaev, R.S. Zaripova, R.R. Galyamov, A.Y. Sharifullina (2019). The use of industrial wireless networks based on standard ISA-100.11a and protocol WirelessHART in process control / E3S Web of Conferences. Vol. 124.
4. V.K. Shcherbo (2000). Computer Network Standards. Interconnection of networks. Moscow: Kudits-obraz. 268 p.
5. V.G. Olifer, N.A. Olifer (2010). Computer networks. Principles, technologies, protocols, Peter, St. Petersburg. 944 p.
6. P. Roshan, J. Lairi (2004). Fundamentals of building wireless local area networks of 802.11 standard: Translated from English, Publishing House «Williams», Moscow. 304 p.
7. A.K. Shcherbakov (2005). Wi-Fi is everything you wanted to know, but were afraid to ask «, Buk-Press. 129 p.
Information about authors:
Albina Yu. Sharifullina, Snr. Lecture, Kazan National Research Technological University, control and automation faculty, department of Process Automation and Control Systems, Kazan, Russia
Roman R. Galyamov, Snr. Lecture, Kazan National Research Technological University, control and automation faculty, department of Process Automation and Control Systems, Kazan, Russia
Rimma S. Zaripova, c.t.s, docent, Kazan National Research Technological University, control and automation faculty, department of Process Automation and Control Systems, c.t.s, docent, Kazan State Power Engineering University, Institute of Digital Technologies and Economics, department of Engineering Cybernetics, Kazan, Russia